Re: [PATCH v2 10/11] arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: Add ov02c10 RGB sensor on CSIPHY4

[Neil Armstrong]

On 3/16/26 02:12, Bryan O'Donoghue wrote:
> Add in the RGB sensor on CSIPHY4.
>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
> ---
>   .../boot/dts/qcom/x1e80100-lenovo-yoga-slim7x.dts  | 77 ++++++++++++++++++++++
>   1 file changed, 77 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-lenovo-yoga-slim7x.dts b/arch/arm64/boot/dts/qcom/x1e80100-lenovo-yoga-slim7x.dts
> index 1611bf7302ddf..b09b437e0cd50 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-lenovo-yoga-slim7x.dts
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-lenovo-yoga-slim7x.dts
> @@ -7,6 +7,7 @@
>   
>   #include <dt-bindings/gpio/gpio.h>
>   #include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/phy/phy.h>
>   #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>   
>   #include "hamoa.dtsi"
> @@ -863,6 +864,66 @@ &gpu_zap_shader {
>   	firmware-name = "qcom/x1e80100/LENOVO/83ED/qcdxkmsuc8380.mbn";
>   };
>   
> +&camss {
> +	status = "okay";
> +
> +	ports {
> +		/*
> +		 * port0 => csiphy0
> +		 * port1 => csiphy1
> +		 * port2 => csiphy2
> +		 * port3 => csiphy4
> +		 */
> +		port@3 {
> +			camss_csiphy4_inep0: endpoint@0 {
> +				clock-lanes = <7>;
> +				data-lanes = <0 1>;
> +				remote-endpoint = <&ov02c10_ep>;

This is quite wrong, with the PHY in a separate node, the lanes layout has nothing
to do in the "controller" ports since the sensor is connected to the the PHY which
configures the lanes functions.

The PHY should be a media element in a port/endpoint chain to properly describe the
data flow from the sensor to the controller.

PHY as a separate node is a first step, ideally all components of the CAMSS should be
in separate nodes with port/endpoints describing the whole data interconnection.

Neil

> +			};
> +		};
> +	};
> +};
> +
> +&cci1 {
> +	status = "okay";
> +};
> +
> +&cci1_i2c1 {
> +	camera@36 {
> +		compatible = "ovti,ov02c10";
> +		reg = <0x36>;
> +
> +		reset-gpios = <&tlmm 237 GPIO_ACTIVE_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&cam_rgb_default>;
> +
> +		clocks = <&camcc CAM_CC_MCLK4_CLK>;
> +		assigned-clocks = <&camcc CAM_CC_MCLK4_CLK>;
> +		assigned-clock-rates = <19200000>;
> +
> +		orientation = <0>; /* front facing */
> +
> +		avdd-supply = <&vreg_l7b_2p8>;
> +		dvdd-supply = <&vreg_l1m_1p2>;
> +		dovdd-supply = <&vreg_l3m_1p8>;
> +
> +		port {
> +			ov02c10_ep: endpoint {
> +				data-lanes = <1 2>;
> +				link-frequencies = /bits/ 64 <400000000>;
> +				remote-endpoint = <&camss_csiphy4_inep0>;
> +			};
> +		};
> +	};
> +};
> +
> +&csiphy4 {
> +	vdda-0p8-supply = <&vreg_l2c_0p8>;
> +	vdda-1p2-supply = <&vreg_l1c_1p2>;
> +
> +	status = "okay";
> +};
> +
>   &i2c0 {
>   	clock-frequency = <400000>;
>   
> @@ -1410,6 +1471,22 @@ &tlmm {
>   			       <44 4>, /* SPI (TPM) */
>   			       <238 1>; /* UFS Reset */
>   
> +	cam_rgb_default: cam-rgb-default-state {
> +		mclk-pins {
> +			pins = "gpio100";
> +			function = "cam_aon";
> +			drive-strength = <16>;
> +			bias-disable;
> +		};
> +
> +		reset-n-pins {
> +			pins = "gpio237";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-disable;
> +		};
> +	};
> +
>   	edp_reg_en: edp-reg-en-state {
>   		pins = "gpio70";
>   		function = "gpio";