Re: [PATCH v3 1/2] dt-bindings: input: add OnePlus pogo-pin keyboard

[Krzysztof Kozlowski]

On Wed, Oct 14, 2026 at 08:52:50AM -0500, wyibo6109@xxxxxxxxx wrote:
> From: Yibo Wang <wyibo6109@xxxxxxxxx>
> 
> Binding for the Tinno keyboard MCU used by the OnePlus Pad 3 Pro /
> Pad 4 and OPPO Pad 5 Pro smart keyboards, attached to a tablet UART.
> Describes the supply, TX-gate and wake GPIOs, with a MAINTAINERS entry.
> 
> The compatible names the tablet project the pogo port belongs to
> (caihong, erhai or iceland), which pins the keyboard MCU generation
> and with it the protocol extensions the host may use: the 0x3A general
> sub-commands grew over time, from the caihong (sm8650 era) MCUs with
> neither wake notification nor backlight, through erhai (sm8750 era,
> wake notification) to iceland (sm8850 era, keyboard backlight).
> 
> The touchpad geometry and the product names are fixed per project and
> live in the driver; the common touchscreen properties
> (touchscreen-size-x/y, touchscreen-x-mm/y-mm) remain as an optional
> override if a variant ever needs one.

Why? It's fixed. It cannot be overridden. Your example DTS even shows
that.

> 
> Signed-off-by: Yibo Wang <wyibo6109@xxxxxxxxx>
> ---
>  .../bindings/input/oneplus,pogo-keyboard.yaml | 73 +++++++++++++++++++
>  MAINTAINERS                                   |  6 ++
>  2 files changed, 79 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/input/oneplus,pogo-keyboard.yaml
> 
> diff --git a/Documentation/devicetree/bindings/input/oneplus,pogo-keyboard.yaml b/Documentation/devicetree/bindings/input/oneplus,pogo-keyboard.yaml
> new file mode 100644
> index 000000000..fa1579ed5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/input/oneplus,pogo-keyboard.yaml
> @@ -0,0 +1,73 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (c) 2026 Yibo Wang <wyibo6109@xxxxxxxxx>
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/input/oneplus,pogo-keyboard.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: OnePlus / OPPO Pad pogo-pin smart keyboard
> +
> +maintainers:
> +  - Yibo Wang <wyibo6109@xxxxxxxxx>
> +
> +description: |
> +  The Tinno keyboard MCU used by the OnePlus Pad 3 Pro / Pad 4 and OPPO
> +  Pad 5 Pro smart keyboards.  It is attached to a tablet UART and speaks
> +  a framed half-duplex protocol over a shared single wire; host
> +  transmission is gated onto the wire by a PMIC GPIO for the duration of
> +  a frame.  The device provides a keyboard matrix, a touchpad and a
> +  keyboard backlight.
> +
> +allOf:
> +  - $ref: /schemas/serial/serial-peripheral-props.yaml#
> +  - $ref: /schemas/input/touchscreen/touchscreen.yaml#

So this is not really needed, drop

> +
> +properties:
> +  compatible:
> +    description: |
> +      Names the tablet project the pogo port belongs to, which pins the
> +      keyboard MCU generation and the protocol extensions the host may
> +      use: caihong (sm8650 era) supports neither the wake notification
> +      nor a backlight, erhai (sm8750 era) adds the wake notification,
> +      iceland (sm8850 era) adds the keyboard backlight.
> +    enum:
> +      - oneplus,caihong-pogo-keyboard
> +      - oneplus,erhai-pogo-keyboard
> +      - oneplus,iceland-pogo-keyboard
> +
> +  power-gpios:
> +    description: GPIO enabling the keyboard supply, held high while attached.
> +    maxItems: 1
> +
> +  tx-enable-gpios:
> +    description: GPIO gating host TX onto the shared one-wire bus.
> +    maxItems: 1
> +
> +  wake-gpios:
> +    description: GPIO signalling attach/detach, also used as the wake line.
> +    maxItems: 1
> +
> +  touchscreen-size-x: true
> +  touchscreen-size-y: true
> +  touchscreen-x-mm: true
> +  touchscreen-y-mm: true

Drop all four.

Best regards,
Krzysztof