Re: [PATCH v2 net-next 2/3] dt-bindings: dpll: add SiTime SiT9531x clock generator

[Krzysztof Kozlowski]

On 20/05/2026 21:19, Ali Rouhi wrote:
> Add device tree binding documentation for the SiTime SiT95316
> and SiT95317 DPLL clock generators.
> 
> Co-developed-by: Oleg Zadorozhnyi <Oleg.Zadorozhnyi@xxxxxxxxxxxxxxxxx>
> Signed-off-by: Oleg Zadorozhnyi <Oleg.Zadorozhnyi@xxxxxxxxxxxxxxxxx>
> Signed-off-by: Ali Rouhi <arouhi@xxxxxxxxxx>

Mismatched DCO. Use consistent identity or fix your commits.

> ---
>  .../bindings/dpll/sitime,sit9531x.yaml        | 145 ++++++++++++++++++
>  1 file changed, 145 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/dpll/sitime,sit9531x.yaml
> 
> diff --git a/Documentation/devicetree/bindings/dpll/sitime,sit9531x.yaml b/Documentation/devicetree/bindings/dpll/sitime,sit9531x.yaml
> new file mode 100644
> index 000000000000..ac88f2f0b2ae
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dpll/sitime,sit9531x.yaml
> @@ -0,0 +1,145 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/dpll/sitime,sit9531x.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: SiTime SiT9531x DPLL Clock Generator
> +
> +maintainers:
> +  - Ali Rouhi <arouhi@xxxxxxxxxx>
> +
> +description: |
> +  SiTime SiT95316 and SiT95317 are I2C-controlled programmable clock
> +  generators with integrated DPLL for synchronization applications.  Both
> +  variants contain four PLLs with automatic/manual reference selection,
> +  DCO frequency adjustment, and phase offset measurement via an on-chip
> +  TDC (Time-to-Digital Converter).
> +
> +  SiT95317 provides 4 inputs and 8 outputs; SiT95316 provides
> +  4 inputs and 12 outputs.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - sitime,sit95316
> +      - sitime,sit95317
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +    description:
> +      External crystal/oscillator feeding the chip's XIN/XO_CLK input.
> +      The chip's PLL Fvco is computed relative to this reference, so the
> +      driver requires a non-zero rate at probe time.

Same as last time. Why are you describing drivers?

> +
> +  clock-names:
> +    items:
> +      - const: xtal
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description:
> +      GPIO connected to the chip's active-low reset pin (RESETB).
> +
> +  interrupts:
> +    maxItems: 1
> +    description:
> +      Interrupt from the chip's active-low INTRB output.  Asserted when
> +      the device detects a status change such as lock acquisition or loss.
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +
> +allOf:
> +  - $ref: /schemas/dpll/dpll-device.yaml#
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    xo: xo {
> +        compatible = "fixed-clock";
> +        #clock-cells = <0>;
> +        clock-frequency = <48000000>;
> +    };

Drop node. Wasn't here before, so why did you add it?


> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        dpll@68 {
> +            compatible = "sitime,sit95317";
> +            reg = <0x68>;
> +            clocks = <&xo>;
> +            clock-names = "xtal";
> +        };
> +    };
> +
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    xo2: xo2 {
> +        compatible = "fixed-clock";
> +        #clock-cells = <0>;
> +        clock-frequency = <48000000>;
> +    };

Drop.

> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +



Best regards,
Krzysztof