Re: [PATCH v3 1/4] dt-bindings: clock: qcom: Add QREF regulator supplies for glymur

[Krzysztof Kozlowski]

On 18/05/2026 05:35, Qiang Yu wrote:
> On Sun, May 17, 2026 at 10:28:48AM +0200, Krzysztof Kozlowski wrote:
>> On 17/05/2026 07:58, Qiang Yu wrote:
>>> On Thu, May 14, 2026 at 12:35:19PM +0200, Krzysztof Kozlowski wrote:
>>>> On 14/05/2026 12:22, Krzysztof Kozlowski wrote:
>>>>> On Wed, May 06, 2026 at 01:43:51AM -0700, Qiang Yu wrote:
>>>>>> Add regulator supply properties for the Glymur TCSR QREF/REFGEN blocks
>>>>>> required by clkref clocks.
>>>>>>
>>>>>> The vdda-qreftx*, vdda-qrefrpt*, and vdda-qrefrx* supplies map to common
>>>>>> QREF TX/RPT/RX components, while SoC-specific topology and instance count
>>>>>> differ. Document them here for qcom,glymur-tcsr.
>>>>>>
>>>>>> Signed-off-by: Qiang Yu <qiang.yu@xxxxxxxxxxxxxxxx>
>>>>>> ---
>>>>>>  .../bindings/clock/qcom,sm8550-tcsr.yaml           | 57 ++++++++++++++++++++++
>>>>>>  1 file changed, 57 insertions(+)
>>>>>>
>>>>>> diff --git a/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml b/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml
>>>>>> index 1ccdf4b0f5dd..57921cb63230 100644
>>>>>> --- a/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/clock/qcom,sm8550-tcsr.yaml
>>>>>> @@ -51,6 +51,63 @@ properties:
>>>>>>    '#reset-cells':
>>>>>>      const: 1
>>>>>>  
>>>>>> +  vdda-refgen-0p9-supply: true
>>>>>> +  vdda-refgen-1p2-supply: true
>>>>>> +  vdda-qrefrx0-0p9-supply: true
>>>>>> +  vdda-qrefrx1-0p9-supply: true
>>>>>> +  vdda-qrefrx2-0p9-supply: true
>>>>>> +  vdda-qrefrx4-0p9-supply: true
>>>>>> +  vdda-qrefrx5-0p9-supply: true
>>>>>> +  vdda-qreftx0-0p9-supply: true
>>>>>> +  vdda-qreftx0-1p2-supply: true
>>>>>> +  vdda-qreftx1-0p9-supply: true
>>>>>> +  vdda-qrefrpt0-0p9-supply: true
>>>>>> +  vdda-qrefrpt1-0p9-supply: true
>>>>>> +  vdda-qrefrpt2-0p9-supply: true
>>>>>> +  vdda-qrefrpt3-0p9-supply: true
>>>>>> +  vdda-qrefrpt4-0p9-supply: true
>>>>>
>>>>> Either I do not understand your previous explanation:
>>>>> CXO -> TX0 -> RPT0 -> RPT1 -> RPT2 -> RX2 -> PCIe4_PHY
>>>>>
>>>>> or this is still wrong. There is no TCSR here, so this proves nothing.
>>>>> If TCSR is TX0, then you do not have five of them...
>>>>>
>>>>> My previous comment stay - you are not describing the actual hardware
>>>>> here.
>>>>
>>>> And it should not be my task BUT YOURS to verify this in hardware
>>>> programming guide or manual, but nevertheless I did verify and the
>>>> manual DOES NOT mention these supplies. For Glymur, it mentions 8 reset
>>>> ports and 5 clock ports.
>>>>
>>>> No supplies at all.
>>>>
>>>> Then I went to QREF and it does mention few supplies but completely
>>>> different, like mx, cx, px 0.88 and px1.2, so none of this matches QREF
>>>> either.
>>>>
>>>
>>> Honestly, I couldn't find QREF LDO-related information in HPG either.
>>> However, you can find it on IPCAT. For example, in the glymur power grid,
>>> these LDOs are clearly documented under the LDOs required by each PHY,
>>
>> How is that relevant here? This is not PHY here. You are adding supplies
>> to TCSR. Do you understand what a supply is?
>>
> 
> I'm telling you the fact that I see from power grid table.

So you see supplies in phy, then add them to the phy.

Best regards,
Krzysztof