[PATCH] arm64: dts: rockchip: Enable Wi-Fi on the NanoPi M5

[Leonard Lausen]

The NanoPi M5 has an M.2 E-key slot for SDIO Wi-Fi modules such as the
RTL8822CS-based AC200. The SDIO controller is disabled and the module's
power sequence is not described, preventing the card from enumerating.

Enable the controller in four-bit SDR104 mode and connect its 3.3 V card
and 1.8 V I/O supplies. Describe the active-low reset on GPIO1_C2, the
200 ms power-on delay used by the vendor device tree, and the external
32.768 kHz clock from the HYM8563 RTC. Keep the card powered during
suspend as required by the rtw88 SDIO driver.

Signed-off-by: Leonard Lausen <leonard@xxxxxxxxx>
---
 .../boot/dts/rockchip/rk3576-nanopi-m5.dts    | 34 +++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3576-nanopi-m5.dts b/arch/arm64/boot/dts/rockchip/rk3576-nanopi-m5.dts
index 3a305408fa16c..bfa18de1ae1af 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576-nanopi-m5.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3576-nanopi-m5.dts
@@ -23,6 +23,7 @@ aliases {
 		ethernet0 = &gmac0;
 		ethernet1 = &gmac1;
 		mmc0 = &sdmmc;
+		mmc1 = &sdio;
 	};
 
 	chosen {
@@ -212,6 +213,16 @@ vcc_3v3_s0: regulator-vcc-3v3-s0 {
 		vin-supply = <&vcc_3v3_s3>;
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&hym8563>;
+		clock-names = "ext_clock";
+		pinctrl-0 = <&wifi_reg_on_h>;
+		pinctrl-names = "default";
+		post-power-on-delay-ms = <200>;
+		reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+	};
+
 	sound {
 		compatible = "simple-audio-card";
 		pinctrl-names = "default";
@@ -855,6 +866,12 @@ pcie0_perstn: pcie0-perstn {
 		};
 	};
 
+	sdio-pwrseq {
+		wifi_reg_on_h: wifi-reg-on-h {
+			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	sdmmc {
 		sdmmc0_pwren_h: sdmmc0-pwren-h {
 			rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>;
@@ -890,6 +907,23 @@ &saradc {
 	status = "okay";
 };
 
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	disable-wp;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	no-mmc;
+	no-sd;
+	non-removable;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vcc_1v8_s3>;
+
+	status = "okay";
+};
+
 &sdmmc {
 	bus-width = <4>;
 	cap-sd-highspeed;
-- 
2.47.3