[PATCH v5 1/4] dt-bindings: iio: adc: add AD4691 family

From: Radu Sabau via B4 Relay

Date: Fri Mar 27 2026 - 07:18:33 EST

From: Radu Sabau <radu.sabau@xxxxxxxxxx>

Add DT bindings for the Analog Devices AD4691 family of multichannel
SAR ADCs (AD4691, AD4692, AD4693, AD4694).

The binding describes the hardware connections:

- Power domains: avdd-supply (required), vio-supply, ref-supply or
refin-supply (external reference; the REFIN path enables the
internal reference buffer), and an optional ldo-in-supply, that if
absent, means the on-chip internal LDO will be used.

- Optional PWM on the CNV pin selects CNV Burst Mode; when absent,
Manual Mode is assumed with CNV tied to SPI CS.

- An optional reset GPIO (reset-gpios) for hardware reset.

- Up to four GP pins (gp0..gp3) usable as interrupt sources,
identified in firmware via interrupt-names "gp0".."gp3".

- gpio-controller with #gpio-cells = <2> for GP pin GPIO usage.

- #trigger-source-cells = <1>: one cell selecting the GP pin number
(0-3) used as the SPI offload trigger source.

Two binding examples are provided: CNV Burst Mode with SPI offload
(DMA data acquisition driven by DATA_READY on a GP pin), and Manual
Mode for CPU-driven triggered-buffer or single-shot capture.

Signed-off-by: Radu Sabau <radu.sabau@xxxxxxxxxx>
---
.../devicetree/bindings/iio/adc/adi,ad4691.yaml | 162 +++++++++++++++++++++
MAINTAINERS | 7 +
2 files changed, 169 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad4691.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad4691.yaml
new file mode 100644
index 000000000000..81d2ca4e0e22
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad4691.yaml
@@ -0,0 +1,162 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/adi,ad4691.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD4691 Family Multichannel SAR ADCs
+
+maintainers:
+ - Radu Sabau <radu.sabau@xxxxxxxxxx>
+
+description: |
+ The AD4691 family are high-speed, low-power, multichannel successive
+ approximation register (SAR) analog-to-digital converters (ADCs) with
+ an SPI-compatible serial interface. The ADC supports CNV Burst Mode,
+ where an external PWM drives the CNV pin, and Manual Mode, where CNV
+ is directly tied to the SPI chip-select.
+
+ Datasheets:
+ * https://www.analog.com/en/products/ad4691.html
+ * https://www.analog.com/en/products/ad4692.html
+ * https://www.analog.com/en/products/ad4693.html
+ * https://www.analog.com/en/products/ad4694.html
+
+$ref: /schemas/spi/spi-peripheral-props.yaml#
+
+properties:
+ compatible:
+ enum:
+ - adi,ad4691
+ - adi,ad4692
+ - adi,ad4693
+ - adi,ad4694
+
+ reg:
+ maxItems: 1
+
+ spi-max-frequency:
+ maximum: 40000000
+
+ spi-cpol: true
+ spi-cpha: true
+
+ avdd-supply:
+ description: Analog power supply (4.5V to 5.5V).
+
+ ldo-in-supply:
+ description: LDO input supply. When absent, the internal LDO is used.
+
+ vio-supply:
+ description: I/O voltage supply (1.71V to 1.89V or VDD).
+
+ ref-supply:
+ description: External reference voltage supply (2.4V to 5.25V).
+
+ refin-supply:
+ description: Internal reference buffer input supply.
+
+ reset-gpios:
+ description:
+ GPIO line controlling the hardware reset pin (active-low).
+ maxItems: 1
+
+ pwms:
+ description:
+ PWM connected to the CNV pin. When present, selects CNV Burst Mode where
+ the PWM drives the conversion rate. When absent, Manual Mode is used
+ (CNV tied to SPI CS).
+ maxItems: 1
+
+ interrupts:
+ description:
+ Interrupt lines connected to the ADC GP pins. Each GP pin can be
+ physically wired to an interrupt-capable input on the SoC.
+ maxItems: 4
+
+ interrupt-names:
+ description: Names of the interrupt lines, matching the GP pin names.
+ minItems: 1
+ maxItems: 4
+ items:
+ enum:
+ - gp0
+ - gp1
+ - gp2
+ - gp3
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ '#trigger-source-cells':
+ description:
+ This node can act as a trigger source. The single cell in a consumer
+ reference specifies the GP pin number (0-3) used as the trigger output.
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - avdd-supply
+ - vio-supply
+
+allOf:
+ # ref-supply and refin-supply are mutually exclusive, one is required
+ - oneOf:
+ - required:
+ - ref-supply
+ - required:
+ - refin-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ /* AD4692 in CNV Burst Mode with SPI offload */
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad4692";
+ reg = <0>;
+ spi-cpol;
+ spi-cpha;
+ spi-max-frequency = <40000000>;
+
+ avdd-supply = <&avdd_supply>;
+ vio-supply = <&vio_supply>;
+ ref-supply = <&ref_5v>;
+
+ reset-gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+
+ pwms = <&pwm_gen 0 0>;
+
+ #trigger-source-cells = <1>;
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ /* AD4692 in Manual Mode (CNV tied to SPI CS) */
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad4692";
+ reg = <0>;
+ spi-cpol;
+ spi-cpha;
+ spi-max-frequency = <31250000>;
+
+ avdd-supply = <&avdd_supply>;
+ vio-supply = <&vio_supply>;
+ refin-supply = <&refin_supply>;
+
+ reset-gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 61bf550fd37c..438ca850fa1c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1484,6 +1484,13 @@ W: https://ez.analog.com/linux-software-drivers
F: Documentation/devicetree/bindings/iio/adc/adi,ad4170-4.yaml
F: drivers/iio/adc/ad4170-4.c

+ANALOG DEVICES INC AD4691 DRIVER
+M: Radu Sabau <radu.sabau@xxxxxxxxxx>
+L: linux-iio@xxxxxxxxxxxxxxx
+S: Supported
+W: https://ez.analog.com/linux-software-drivers
+F: Documentation/devicetree/bindings/iio/adc/adi,ad4691.yaml
+
ANALOG DEVICES INC AD4695 DRIVER
M: Michael Hennerich <michael.hennerich@xxxxxxxxxx>
M: Nuno Sá <nuno.sa@xxxxxxxxxx>

--
2.43.0