Re: [PATCH v5 1/2] dt-bindings: phy: qcom: Add CSI2 C-PHY/DPHY schema
From: Vladimir Zapolskiy
Date: Wed Mar 25 2026 - 21:59:20 EST
On 3/26/26 03:04, Bryan O'Donoghue wrote:
Add a base schema initially compatible with x1e80100 to describe MIPI CSI2
PHY devices.
The hardware can support both CPHY, DPHY and a special split-mode DPHY. We
capture those modes as:
- PHY_QCOM_CSI2_MODE_DPHY
- PHY_QCOM_CSI2_MODE_CPHY
- PHY_QCOM_CSI2_MODE_SPLIT_DPHY
Distinction between PHY_QCOM_CSI2_MODE_DPHY and PHY_QCOM_CSI2_MODE_SPLIT_DPHY
is
1) insufficient in just this simplistic form, because the assignment of
particular lanes is also needed,
2) and under the assumption that the lane mapping is set somewhere else, then
there should be no difference between PHY_QCOM_CSI2_MODE_{DPHY,SPLIT_DPHY},
it's just DPHY, and the subtype is deductible from data-lanes property on
the consumer side.
So far the rationale is unclear, why anything above regular PHY_TYPE_DPHY
and PHY_TYPE_CPHY is needed here, those two are sufficient.
The CSIPHY devices have their own pinouts on the SoC as well as their own
individual voltage rails.
The need to model voltage rails on a per-PHY basis leads us to define
CSIPHY devices as individual nodes.
Two nice outcomes in terms of schema and DT arise from this change.
1. The ability to define on a per-PHY basis voltage rails.
2. The ability to require those voltage.
We have had a complete bodge upstream for this where a single set of
voltage rail for all CSIPHYs has been buried inside of CAMSS.
Much like the I2C bus which is dedicated to Camera sensors - the CCI bus in
CAMSS parlance, the CSIPHY devices should be individually modelled.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx>
---
.../bindings/phy/qcom,x1e80100-csi2-phy.yaml | 130 +++++++++++++++++++++
include/dt-bindings/phy/phy-qcom-mipi-csi2.h | 15 +++
2 files changed, 145 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
new file mode 100644
index 0000000000000..63114151104b4
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/qcom,x1e80100-csi2-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm CSI2 PHY
+
+maintainers:
+ - Bryan O'Donoghue <bod@xxxxxxxxxx>
+
+description:
+ Qualcomm MIPI CSI2 C-PHY/D-PHY combination PHY. Connects MIPI CSI2 sensors
+ to Qualcomm's Camera CSI Decoder. The PHY supports both C-PHY and D-PHY
+ modes.
+
+properties:
+ compatible:
+ const: qcom,x1e80100-csi2-phy
+
+ reg:
+ maxItems: 1
+
+ "#phy-cells":
+ const: 1
+ description:
+ The single cell specifies the PHY operating mode.
+ See include/dt-bindings/phy/phy-qcom-mipi-csi2.h for valid values.
include/dt-bindings/phy/phy.h should be good enough as it's stated above.
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: core
+ - const: timer
+
+ interrupts:
+ maxItems: 1
+
+ operating-points-v2:
+ maxItems: 1
+
+ power-domains:
+ items:
+ - description: MXC or MXA voltage rail
+ - description: MMCX voltage rail
+
+ power-domain-names:
+ items:
+ - const: mx
+ - const: mmcx
+
+ vdda-0p9-supply:
+ description: Phandle to a 0.9V regulator supply to a PHY.
+
+ vdda-1p2-supply:
+ description: Phandle to 1.2V regulator supply to a PHY.
+
+required:
+ - compatible
+ - reg
+ - "#phy-cells"
+ - clocks
+ - clock-names
+ - interrupts
+ - operating-points-v2
+ - power-domains
+ - power-domain-names
+ - vdda-0p9-supply
+ - vdda-1p2-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/qcom,x1e80100-camcc.h>
+ #include <dt-bindings/clock/qcom,x1e80100-gcc.h>
+ #include <dt-bindings/phy/phy-qcom-mipi-csi2.h>
+ #include <dt-bindings/power/qcom,rpmhpd.h>
+
+ csiphy4: csiphy@ace4000 {
+ compatible = "qcom,x1e80100-csi2-phy";
+ reg = <0x0ace4000 0x2000>;
+ #phy-cells = <1>;
+
+ clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
+ <&camcc CAM_CC_CSI0PHYTIMER_CLK>;
+ clock-names = "core",
+ "timer";
+
+ operating-points-v2 = <&csiphy_opp_table>;
+
+ interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
+
+ power-domains = <&rpmhpd RPMHPD_MX>,
+ <&rpmhpd RPMHPD_MMCX>;
+ power-domain-names = "mx",
+ "mmcx";
+
+ vdda-0p9-supply = <&vreg_l2c_0p8>;
+ vdda-1p2-supply = <&vreg_l1c_1p2>;
+ };
+
+ csiphy_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_low_svs_d1>,
+ <&rpmhpd_opp_low_svs_d1>;
+ };
+
+ opp-400000000 {
+ opp-hz = /bits/ 64 <400000000>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+ };
+ };
+
+ isp@acb7000 {
+ phys = <&csiphy4 PHY_QCOM_CSI2_MODE_DPHY>;
+ };
This example is incomplete in sense that it does not include CAMSS
CSIPHY IP hardware configuration in whole.
diff --git a/include/dt-bindings/phy/phy-qcom-mipi-csi2.h b/include/dt-bindings/phy/phy-qcom-mipi-csi2.h
new file mode 100644
index 0000000000000..fa48fd75c58d8
--- /dev/null
+++ b/include/dt-bindings/phy/phy-qcom-mipi-csi2.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) */
+/*
+ * Qualcomm MIPI CSI2 PHY constants
+ *
+ * Copyright (C) 2026 Linaro Limited
+ */
+
+#ifndef __DT_BINDINGS_PHY_MIPI_CSI2__
+#define __DT_BINDINGS_PHY_MIPI_CSI2__
+
+#define PHY_QCOM_CSI2_MODE_DPHY 0
+#define PHY_QCOM_CSI2_MODE_CPHY 1
+#define PHY_QCOM_CSI2_MODE_SPLIT_DPHY 2
+
+#endif /* __DT_BINDINGS_PHY_MIPI_CSI2__ */
--
Best wishes,
Vladimir