Re: [PATCH RFC] drm/msm/dpu: calculate data_width like downstream

[Dmitry Baryshkov]

On Sun, Mar 22, 2026 at 02:31:13PM +0000, Alexander Koskovich wrote:
> Derive INTF data_width from dce_bytes_per_line rather than
> timing->width when DSC is enabled. Use DIV_ROUND_UP to avoid
> rounding errors.
> 
> Signed-off-by: Alexander Koskovich <akoskovich@xxxxx>
> ---
> This patch changes the data_width calculation to match downstream,
> and avoids needing to change the divisor for timing->width to /24.
> 
> However I am not sure if this is a correct approach, but at least
> with this I get the same values for data_width as downstream now:
> 
> data_width w/ no widebus
> before: 288
> after: 360
> 
> data_with w/ widebus
> before: 144
> after: 180
> 
> This was tested with the BOE BF068MWM-TD0 on the Nothing Phone (3a),
> it would be greatly appreciated if someone from QCOM could weigh in
> on if this is a correct approach.
> 
> Tested with kmscube and getting 120FPS, also note that this was
> tested with a few other changes:
> 
> (drm/msm/dsi: fix hdisplay calculation when programming dsi registers)

This is a part of msm-fixes

> (drm/msm/dsi: fix pclk rate calculation for bonded dsi)

This is a part of msm-fixes

> (drm/msm/dsi: fix bits_per_pclk)
> (drm/msm/dsi: fix hdisplay calculation for CMD mode panel)

Okay, let's pick these two. I assume we've had enough of testing. I hope
Marijn can also r-b those.

> ---
>  .../gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c   |  2 ++
>  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c        | 23 +++++++++++++++++-----
>  drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h        |  1 +
>  3 files changed, 21 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> index 0ba777bda253..ba810f26ea30 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c
> @@ -10,6 +10,7 @@
>  #include "dpu_formats.h"
>  #include "dpu_trace.h"
>  #include "disp/msm_disp_snapshot.h"
> +#include "msm_dsc_helper.h"
>  
>  #include <drm/display/drm_dsc_helper.h>
>  #include <drm/drm_managed.h>
> @@ -136,6 +137,7 @@ static void drm_mode_to_intf_timing_params(
>  		timing->width = timing->width * drm_dsc_get_bpp_int(dsc) /
>  				(dsc->bits_per_component * 3);
>  		timing->xres = timing->width;
> +		timing->dce_bytes_per_line = msm_dsc_get_bytes_per_line(dsc);
>  	}
>  }
>  
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> index 7e620f590984..de6b5b0f70c4 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c
> @@ -173,13 +173,26 @@ static void dpu_hw_intf_setup_timing_engine(struct dpu_hw_intf *intf,
>  	data_width = p->width;
>  
>  	/*
> -	 * If widebus is enabled, data is valid for only half the active window
> -	 * since the data rate is doubled in this mode. But for the compression
> -	 * mode in DP case, the p->width is already adjusted in
> -	 * drm_mode_to_intf_timing_params()

Please keep the DP comment. We need to fix the assymmetry between DSI
and DP, but that needs DP DSC support first.


With that in place, the patch LGTM.

> +	 * If widebus is disabled:
> +	 * For uncompressed stream, the data is valid for the entire active
> +	 * window period.
> +	 * For compressed stream, data is valid for a shorter time period
> +	 * inside the active window depending on the compression ratio.
> +	 *
> +	 * If widebus is enabled:
> +	 * For uncompressed stream, data is valid for only half the active
> +	 * window, since the data rate is doubled in this mode.
> +	 * For compressed stream, data validity window needs to be adjusted for
> +	 * compression ratio and then further halved.
>  	 */
> -	if (p->wide_bus_en && !dp_intf)
> +	if (p->compression_en && !dp_intf) {
> +		if (p->wide_bus_en)
> +			data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 6);
> +		else
> +			data_width = DIV_ROUND_UP(p->dce_bytes_per_line, 3);

I was concerned about DPU < 5.0, but data_width is only used for
HCTL-related timings, which means DPU 5.0+. I'll look at restructuring
the code.

> +	} else if (p->wide_bus_en && !dp_intf) {
>  		data_width = p->width >> 1;
> +	}
>  
>  	/* TODO: handle DSC+DP case, we only handle DSC+DSI case so far */
>  	if (p->compression_en && !dp_intf &&
> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> index f6ef2c21b66d..badd26305fc9 100644
> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.h
> @@ -35,6 +35,7 @@ struct dpu_hw_intf_timing_params {
>  
>  	bool wide_bus_en;
>  	bool compression_en;
> +	u32 dce_bytes_per_line;
>  };
>  
>  struct dpu_hw_intf_prog_fetch {
> 
> ---
> base-commit: f338e77383789c0cae23ca3d48adcc5e9e137e3c
> change-id: 20260322-fix-data-width-calc-c44287df08b8
> 
> Best regards,
> -- 
> Alexander Koskovich <akoskovich@xxxxx>
> 
> 

-- 
With best wishes
Dmitry