[PATCH v5] arm64: dts: qcom: glymur-crd: Enable keyboard, trackpad and touchscreen
From: Abel Vesa
Date: Thu Mar 19 2026 - 11:35:26 EST
On CRD, the keyboard, trackpad and touchscreen are connected over I2C
and all share a 3.3V regulator.
So describe the regulator and each input device along with their
pinctrl states.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxxxxxxxx>
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxxxx>
Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxxxxxxxx>
---
Changes in v5:
- Since this depends on Displat DT patchset and since that one
had to be respun in order to drop the non-merging phy patch
dependency, this one had to be respun as well so that the dependency
tree is correct.
- Link to v4: https://patch.msgid.link/20260319-glymur-dts-crd-enable-kbd-tp-ts-v4-1-dfe67a134996@xxxxxxxxxxxxxxxx
Changes in v4:
- Rebased on next-20260318.
- Dropped all dependencies except the USB DT and Display DT patchesets,
which are needed for this one to apply cleanly.
- Link to v3: https://patch.msgid.link/20260313-glymur-dts-crd-enable-kbd-tp-ts-v3-1-66c5ddfee97d@xxxxxxxxxxxxxxxx
Changes in v3:
- Picked up Dmitry's and Konrad's R-b tags.
- Drop the output-high and add bias-disable to the reset pin of the
touchscreen default state.
- Link to v2: https://patch.msgid.link/20260312-glymur-dts-crd-enable-kbd-tp-ts-v2-1-2277bee4c564@xxxxxxxxxxxxxxxx
Changes in v2:
- Rebased on next-20260311
- Re-ordered pinctrl properties in vreg_misc_3p3, as Konrad suggested.
- Dropped next level dependency patchset.
- Link to v1: https://patch.msgid.link/20260309-glymur-dts-crd-enable-kbd-tp-ts-v1-1-56e03f769a76@xxxxxxxxxxxxxxxx
---
arch/arm64/boot/dts/qcom/glymur-crd.dts | 117 ++++++++++++++++++++++++++++++++
1 file changed, 117 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dts b/arch/arm64/boot/dts/qcom/glymur-crd.dts
index 38cdcf662ba7..5089ff7cdca3 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dts
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dts
@@ -13,6 +13,8 @@
#include "pmk8850.dtsi" /* SPMI0: SID-0 */
#include "smb2370.dtsi" /* SPMI2: SID-9/10/11 */
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
/ {
model = "Qualcomm Technologies, Inc. Glymur CRD";
compatible = "qcom,glymur-crd", "qcom,glymur";
@@ -139,6 +141,23 @@ vreg_edp_3p3: regulator-edp-3p3 {
regulator-boot-on;
};
+ vreg_misc_3p3: regulator-misc-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_MISC_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmh0110_f_e0_gpios 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&misc_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vreg_nvme: regulator-nvme {
compatible = "regulator-fixed";
@@ -446,6 +465,64 @@ vreg_l4h_e0_1p2: ldo4 {
};
};
+&i2c0 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ touchpad@2c {
+ compatible = "hid-over-i2c";
+ reg = <0x2c>;
+
+ hid-descr-addr = <0x20>;
+ interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l15b_e0_1p8>;
+
+ pinctrl-0 = <&tpad_default>;
+ pinctrl-names = "default";
+
+ wakeup-source;
+ };
+
+ keyboard@3a {
+ compatible = "hid-over-i2c";
+ reg = <0x3a>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l15b_e0_1p8>;
+
+ pinctrl-0 = <&kybd_default>;
+ pinctrl-names = "default";
+
+ wakeup-source;
+ };
+};
+
+&i2c8 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ touchscreen@38 {
+ compatible = "hid-over-i2c";
+ reg = <0x38>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <&vreg_misc_3p3>;
+ vddl-supply = <&vreg_l15b_e0_1p8>;
+
+ pinctrl-0 = <&ts0_default>;
+ pinctrl-names = "default";
+ };
+};
+
&i2c5 {
clock-frequency = <400000>;
@@ -626,6 +703,19 @@ key_vol_up_default: key-vol-up-default-state {
};
};
+&pmh0110_f_e0_gpios {
+ misc_3p3_reg_en: misc-3p3-reg-en-state {
+ pins = "gpio6";
+ function = "normal";
+ bias-disable;
+ input-disable;
+ output-enable;
+ drive-push-pull;
+ power-source = <1>; /* 1.8 V */
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ };
+};
+
&pmk8850_rtc {
qcom,no-alarm;
};
@@ -664,6 +754,33 @@ edp_reg_en: edp-reg-en-state {
bias-disable;
};
+ kybd_default: kybd-default-state {
+ pins = "gpio67";
+ function = "gpio";
+ bias-disable;
+ };
+
+ tpad_default: tpad-default-state {
+ pins = "gpio3";
+ function = "gpio";
+ bias-disable;
+ };
+
+ ts0_default: ts0-default-state {
+ int-n-pins {
+ pins = "gpio51";
+ function = "gpio";
+ bias-disable;
+ };
+
+ reset-n-pins {
+ pins = "gpio48";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
pcie4_default: pcie4-default-state {
clkreq-n-pins {
pins = "gpio147";
---
base-commit: 54526d6c29ce58d5399cd4e2237d631266ebaaef
change-id: 20260309-glymur-dts-crd-enable-kbd-tp-ts-c80c0cb78940
prerequisite-change-id: 20260109-dts-qcom-glymur-add-usb-support-617b6d9d032c:v6
prerequisite-patch-id: 7ec5f802a334d96421d8f95d4d9e9773655cc947
prerequisite-patch-id: 8d9e016b49979fa817cf9eab70b809fdb9d4656f
prerequisite-change-id: 20260109-dts-qcom-glymur-crd-add-edp-03f0adde9750:v6
prerequisite-patch-id: 7ec5f802a334d96421d8f95d4d9e9773655cc947
prerequisite-patch-id: 8d9e016b49979fa817cf9eab70b809fdb9d4656f
prerequisite-patch-id: 346f2db0933c551a039f63b945f989a5c8320657
prerequisite-patch-id: 919020405b70d588fa4356a5cbfb44e67006102e
Best regards,
--
Abel Vesa <abel.vesa@xxxxxxxxxxxxxxxx>